+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
Anti-Static PP Hollow Sheets With Verified Resistivity Grades
You are here: Home » Products » Large Plastic Packaging » Plastic Hollow Board » Anti-Static PP Hollow Sheets With Verified Resistivity Grades
PP Corrugated Sheet

loading

PP Corrugated Sheet PP Corrugated Sheet
PP Corrugated Sheet PP Corrugated Sheet
PP Corrugated Sheet PP Corrugated Sheet
PP Corrugated Sheet PP Corrugated Sheet
PP Corrugated Sheet PP Corrugated Sheet
PP Corrugated Sheet PP Corrugated Sheet

Anti-Static PP Hollow Sheets With Verified Resistivity Grades

Availability:
Quantity:
An electrostatic event leaves no visible mark, only a field failure found at end-of-line test. Anti-static protection works only if the conductive network runs through the whole wall section, not as a coating that wears away in the first month.
Product Description

An electrostatic event leaves no visible mark on a control board, only a latent defect that surfaces at end-of-line test or, worse, in the field. That is why anti-static sheet is specified with measured numbers rather than with the word "anti-static" printed on it.

The grades are defined by surface resistivity. Static-dissipative sheet sits between about 10^6 and 10^11 ohm, slow enough to bleed charge without sparking, fast enough to stop charge accumulating. Conductive sheet drops below 10^6 ohm for applications that need an equipotential path. Choosing between them is a process decision, not a price decision, and it should match the EPA standard your electronics area already works to.

Our protection is carbon-loaded through the wall section. The conductive network of carbon particles runs through every skin and flute layer of the extruded sheet, so the resistivity does not depend on a surface layer that scuffs away in the first month. A scratched dissipative sheet is still a dissipative sheet.

Verification is measured, not claimed. Sheets are tested with a surface-resistance meter on both faces, and each production batch carries readings in its inspection record. For customers with stricter regimes we also run charge-decay testing, reporting the time for a 5 kV charge to fall below 100 V, typically inside two seconds on dissipative grades.

Grounding deserves an honest note: plastic does not ground itself. The sheet equalises charge across its surface and bleeds it through whatever contact path exists, so a container system built from dissipative board works best standing on a conductive shelf or docked to a grounded trolley. We design the contact points with that in mind rather than letting the box float on rubber castors.

The typical uses are predictable and worth naming: ECU and sensor packaging, connector assemblies, populated PCBs in transit between plants, and increasingly battery modules, where stray charge is a safety topic as much as a quality one.

Identification prevents the classic failure: a dissipative container repurposed for ordinary duty and lost from the ESD loop. Conductive grades are black because of the carbon loading, and every sheet can carry a printed ESD symbol and resistivity grade, so a line-side audit can verify at a glance what a box is made of.

Resistivity drifts with age and abuse. Abrasion, UV exposure and contamination all push readings upward over years, so we recommend a scheduled re-measure of container fleets, annually as a baseline, and retire sheets that leave the specified band. A dissipative container that no longer measures is decoration.

Recycling stays possible. Carbon-loaded PP can be reground, though it is kept in a separate stream from natural grades so the regrind colour and resistivity remain predictable for the products made from it.

State the sensitivity class of your components and the EPA standard your line works to, and the specification you receive will name the resistivity band, the decay performance and the verification method rather than just the word anti-static.

Product data parameters
Material
Polypropylene (PP) hollow sheet / corrugated plastic (Coroplast
Corflute
Danpla)
Thickness
2 – 12 mm (custom up to 14 mm)
Weight (GSM)
250 – 3500 g/m²
Max Width
up to 2300 – 2600 mm (standard 1220 mm)
Structure
Twin-wall hollow
corrugated fluted
Colour
White
Black
Blue
Green
Yellow
Red
Gray
Transparent
Pantone custom
Surface Treatment
Corona treated ≥46 dyne/cm (printable)
ESD
conductive
UV-stabilized
fire-rated options
Service Temperature
−20 °C ~ +60 °C
Water Absorption
< 0.01%
Recyclability
100% recyclable PP
Product Catalogue
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.