+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
Layered CNC EVA Liners With Features Split by Depth Level
You are here: Home » Products » Packaging Lining » EVA » Layered CNC EVA Liners With Features Split by Depth Level
EVA foam

loading

EVA foam EVA foam
EVA foam EVA foam
EVA foam EVA foam
EVA foam EVA foam
EVA foam EVA foam
EVA foam EVA foam

Layered CNC EVA Liners With Features Split by Depth Level

Availability:
Quantity:
Deep EVA liners assembled from CNC cut layers: fine locating features held to single layer tolerances, pin and mark alignment between levels, and a replaceable top plate that renews the cavity.
Product Description

A deep, complex cavity cut straight into a thick EVA sheet is expensive twice over. Extra thick sheet is slow to source and hard to cut without tapered walls, and one deep toolpath puts every feature into one pass where a single error ruins the blank. Most of these liners work better built as layers, each level simple and each level carrying only what it must.

layered CNC cut EVA liners for automotive components

The split follows the depth. The top layer holds every fine feature: pocket walls, locating surfaces, engraved part numbers, and the touch faces for finished parts. Middle layers only cut broad openings and support posts, where a generous tolerance is safe. The base layer carries the load path and the interface to the crate. Each layer is cheap to replace and simple to inspect on its own.

Stacking adds tolerance, so the design respects it. Alignment comes from dowel pins and engraved corner marks, and the drawing states the permitted offset per layer and the total. Any dimension that spans two layers is treated as suspect; the features that decide fit are kept inside a single layer, where the cutting tolerance alone governs them.

laminated EVA foam packaging with alignment pin layers

Bonding is the quiet risk. Adhesives are chosen against the cleaning agents in the loop, and glue lines are kept away from part contact faces, where a stiff bead or a squeezed edge can mark a finish. Densities differ by level: a denser top layer holds size under locating loads, lighter layers below give cushioning. Cut edges are sealed so the stack does not shed crumbs.

Daily use rewards the structure. Edge marks show the assembly order at a glance, so layers cannot be stacked in the wrong sequence after washing. The top layer takes the wear from repeated part changes, and replacing it renews the cavity without scrapping the set. A warped or delaminated middle layer is swapped alone, and the crate never waits for a new insert.

replaceable top layer foam insert trays for auto parts

Verification checks the stack, not just the parts. Assembled liners are measured for total thickness, cavity position against the crate, and the offset at each joint. Real parts are fitted, then packs run vibration and a drop, and the wash cycle is included because a glue line is judged after it is wet. Delamination at any joint, not a scratch on a wall, is the retirement signal.

To quote a layered liner, send the part 3D data with its permitted and forbidden contact faces, quantity per box, crate inner dimensions, stacked layers, cleaning agents, temperature range, target cycles, and annual volume. We return a layer drawing showing which features sit on which level, a tolerance and offset table, and samples with a first article and wash recheck record.

Product data parameters
Material
Ethylene-Vinyl Acetate (EVA) foam
closed-cell
cross-linked
VA Content
5% – 40% by weight
Density
30 – 300 kg/m³
Hardness
Shore A 20 – 90 (or Shore C 10 – 90)
Service Temperature
−40 °C ~ +80 °C
Tensile Strength
2 – 20 MPa
Elongation at Break
100% – 600% (up to 800%)
Compression Set
≤ 35% (22h @ 70 °C)
Water Absorption
< 1% by volume
Flame Retardant
UL 94 HB / V-0 (optional)
Product Catalogue
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.