+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
Matching Liner Surface Hardness to the Parts They Protect
You are here: Home » Products » Large Plastic Packaging » Plastic Hollow Board » Matching Liner Surface Hardness to the Parts They Protect
Plastic Corrugated Panel

loading

Plastic Corrugated Panel Plastic Corrugated Panel
Plastic Corrugated Panel Plastic Corrugated Panel
Plastic Corrugated Panel Plastic Corrugated Panel
Plastic Corrugated Panel Plastic Corrugated Panel
Plastic Corrugated Panel Plastic Corrugated Panel
Plastic Corrugated Panel Plastic Corrugated Panel

Matching Liner Surface Hardness to the Parts They Protect

Availability:
Quantity:
A liner is meant to stop wear, but the wrong liner causes it. A hard board face against a polished housing, or a soft foam under a heavy casting, both turn protection into abrasion over a few hundred kilometres.
Product Description

A liner exists to stop wear, but the wrong liner becomes the source of it. A bare board face sliding against a polished housing polishes it into a complaint, and a soft foam pad under a heavy casting takes a permanent impression in the first trip. Pairing the liner surface to the part is therefore the first decision, ahead of thickness and price.

The pairing rule is simple: similar hardness is the worst combination. Two hard surfaces slide against each other under vibration and grind; two very soft ones deform and spread the load. Trouble lives where part and liner are close in hardness, so either go hard with structure or soft with the contact face, deliberately.

The surface menu starts with bare PP board, correct for rugged parts, castings and components that arrive with burrs. A PE film laminate softens the face slightly, adds a wipe-clean layer and suits coated parts that must not pick up board texture. Foam faces in EPE or EPP absorb shock and spread point loads; flocked or felt lining is the finest surface we fit, reserved for visible finishes, glass and plated components.

The two failure modes need opposite answers. Scratching is a sliding problem: it comes from relative movement between part and liner, and it is solved with the softest face that still supports the load. Impressions are a static problem: they come from dwell time under weight, and they are solved with more support area, not softer material. Diagnosis matters, because applying foam to a scratching problem usually creates an impression problem.

Fretting is the hidden mode between the two. A small contact area carrying a real load, moved millimetres a thousand times, wears a bright ring into a hard part that nothing else touched. Wider pads, lower pressure and any face with a slight give reduce it dramatically.

Laminating and flocking are processes, not stickers. PE film is bonded to the board under pressure so it will not peel at the edges after washing; flock is applied electrostatically so the fibres stand up rather than lying flat, which is what actually gives it the soft drag. Both are specified by face weight and adhesion, and both can be quoted with test references.

Hygiene constrains the soft end of the menu. Flocked and felt faces are harder to wash than a laminated board, so they are specified where the finish demands them and avoided in loops that require daily wash-down. A liner that cannot be cleaned properly becomes a hygiene risk regardless of how well it cushions.

Wear is expected and planned for. Faces are the sacrificial layer: they are attached so a worn face can be replaced while the structural board underneath continues in service, which keeps liner maintenance at the cost of a face rather than the whole set.

Verification is practical. A trial set is packed, shipped on a real route and unpacked under good light against the finish standard the part carries; what survives that loop is the specification, not what looked right on the bench.

Describe the part finish, the load it carries and the washing regime the liner must survive, and the reply names the face material, its fixing method and the expected life in cycles.

Product data parameters
Material
Polypropylene (PP) hollow sheet / corrugated plastic (Coroplast
Corflute
Danpla)
Thickness
2 – 12 mm (custom up to 14 mm)
Weight (GSM)
250 – 3500 g/m²
Max Width
up to 2300 – 2600 mm (standard 1220 mm)
Structure
Twin-wall hollow
corrugated fluted
Colour
White
Black
Blue
Green
Yellow
Red
Gray
Transparent
Pantone custom
Surface Treatment
Corona treated ≥46 dyne/cm (printable)
ESD
conductive
UV-stabilized
fire-rated options
Service Temperature
−20 °C ~ +60 °C
Water Absorption
< 0.01%
Recyclability
100% recyclable PP
Product Catalogue
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.