+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
Multi-Wall PP Sheets With the Stiffness Single-Wall Boards Lack
You are here: Home » Products » Large Plastic Packaging » Plastic Hollow Board » Multi-Wall PP Sheets With the Stiffness Single-Wall Boards Lack
Plastic Hollow Board

loading

Plastic Hollow Board Plastic Hollow Board
Plastic Hollow Board Plastic Hollow Board
Plastic Hollow Board Plastic Hollow Board
Plastic Hollow Board Plastic Hollow Board
Plastic Hollow Board Plastic Hollow Board
Plastic Hollow Board Plastic Hollow Board

Multi-Wall PP Sheets With the Stiffness Single-Wall Boards Lack

Availability:
Quantity:
Colour is the part of a multi-wall sheet that everyone notices first. The part that matters once the sheet becomes a container wall is the number of flutes, because stiffness per kilo is decided there.
Product Description

Colour is the part of a multi-wall sheet that gets noticed first, and it is genuinely useful in a plant. But the property that matters once the sheet is fabricated into a container wall is the number of flutes running through it, because bending stiffness per kilogram of plastic is decided there.

A twin-wall sheet carries two skins joined by one layer of vertical flutes. A multi-wall sheet adds flute layers between them, so the cross-section starts to behave like a series of I-beams rather than a single one. The skins take tension and compression; the flutes hold them apart and carry shear. More webs mean more of those beams working in parallel.

The practical consequence shows up in span. Take a panel spanning five hundred millimetres under a side load: a twin-wall sheet of the same weight bows noticeably further than a multi-wall version, because the second flute layer roughly doubles the section depth without doubling the mass. Stiffness rises faster than weight, which is the whole trick.

Flatness is the quieter benefit. Large single-flute panels develop visible waves as they absorb humidity cycles and handling stress, and a wavy panel looks cheap on a returnable container long before it fails. Multi-wall sheets hold their plane, which keeps container walls looking square after a year of service.

Where the structure is used determines the configuration. Crate walls and sleeve panels run multi-wall to resist bulging under a full load; base decks add a second flute direction to spread point loads; lid panels use it to stay flat across a wide span so they close without a gap at the middle.

Fabrication follows the structure. Folding lines are scored between flute layers, not across them, so the fold keeps its stiffness while gaining a hinge. Welding reaches the web layers and fuses the section solid, and every cut edge is sealed, because a multi-wall edge exposes several open cavities rather than one.

Against solid sheet the comparison is about economy at equal stiffness. Matching the bending stiffness of a multi-wall panel with solid PP needs substantially more material per panel, which raises both cost and the tare weight of every container built from it. For walls and decks, the flute structure does the work that solid thickness would otherwise do.

Colour runs through the multi-wall section the same way it runs through a twin-wall one: masterbatch blended at extrusion, pigment present in every layer, so a scratch across the surface does not reveal a different shade underneath. Shade consistency across batches follows the same recorded-formulation discipline as any other coloured sheet.

The additives ride along unchanged: anti-static and conductive grades for electronics duty, flame retardant versions for enclosed spaces, and UV stabilisation for covered outdoor storage, all available on the multi-wall section without changing the geometry.

Bring the container drawing and the loads it must carry, and the answer comes back as a wall configuration, flute direction and gauge chosen for that specific panel.

Product data parameters
Material
Polypropylene (PP) hollow sheet
corrugated plastic (Coroplast/Corflute/Danpla)
Thickness
2 – 12 mm (custom up to 14 mm)
Weight (GSM)
250 – 3500 g/m²
Max Width
up to 2300 – 2600 mm (standard 1220 mm)
Structure
Twin-wall hollow
corrugated fluted
Colour
White
Black
Blue
Green
Yellow
Red
Gray
Transparent
Pantone custom
Surface Treatment
Corona treated ≥46 dyne/cm (printable)
ESD
conductive
UV-stabilized
fire-rated options
Service Temperature
−20 °C ~ +60 °C
Water Absorption
< 0.01%
Recyclability
100% recyclable PP
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.