+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
One-Piece EPP Containers Where the Box and the Liner Are the Same Part
You are here: Home » Products » Packaging Lining » EPP » One-Piece EPP Containers Where the Box and the Liner Are the Same Part
High-quality EPP Containers Are Widely Used in The Automotive Components Industry

loading

High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry
High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry
High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry
High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry
High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry
High-quality EPP Containers Are Widely Used in The Automotive Components Industry High-quality EPP Containers Are Widely Used in The Automotive Components Industry

One-Piece EPP Containers Where the Box and the Liner Are the Same Part

Availability:
Quantity:
The usual container is a rigid shell with soft padding fitted inside, two parts with an interface between them. A one-piece EPP container removes that interface: the wall that carries the load and the surface that cushions the part are moulded in the same operation.
Product Description

The usual container is a rigid shell with soft padding fitted inside, which means two materials, two production routes and an interface where the two meet. That interface is where gaps open up, fixings loosen and dirt collects. A one-piece EPP container removes it entirely: the wall that carries the load and the surface that cushions the part come out of the same mould.

The structure works because EPP is strong for its weight. Bead moulding produces walls with a compressive strength between roughly 0.3 and 2.5 MPa depending on density, so a container body at 60 to 80 kg/m3 carries stacked loads through its walls while the same part density-grades down to 30 kg/m3 at the contact faces that meet the component.

That zoning is built into the mould, not added afterwards. Wall sections, corner columns and lid rims run at the structural grade; the cavities that hold the part are moulded with a lower-density face bonded integrally to the structural layer behind it. There is no adhesive layer to age, no liner to slip and no pocket for moisture between shell and padding.

Weight is the quiet advantage. A moulded EPP container often lands well below the tare of a hard-shell equivalent with fitted liners, because the cushioning layer is doing structural work instead of adding to it. In a fleet counted in hundreds of boxes, tare weight turns directly into freight cost.

Temperature behaviour suits harsh duties. Service range from about −40 °C to +130 °C means the same container design works in cold stores, drying areas and on summer loading docks, and the closed-cell walls absorb essentially no water, so the container neither gains weight nor grows mould in humid loops.

Geometry freedom is where one-piece moulding beats fabrication. Ribs, hooks, stacking ledges, hinge sections and lid latches are all moulded features rather than added hardware, so there are no screws to back out and no welded corners to crack. A container arrives complete from the tool.

The honest trade-offs belong in the text as much as the advantages. Moulded foam surfaces mark more readily than hard shells, so appearance-critical applications specify a darker colour or accept the patina. EPP's low surface energy resists adhesives, which pushes any labelling toward recessed panels. And tooling is a real investment, which makes the one-piece route economical for stable part families rather than short-lived one-offs.

Those limits shape sensible usage. High-value fragile components, battery modules and instrument sets run in one-piece EPP because the protection justifies the tool; bulk fasteners and commodity castings stay in fabricated boxes with standard liners.

End of life is clean. The container is a single polymer, so it recycles as one item rather than as a composite, and moulded EPP can be reground and remoulded into new parts.

Bring the component family and the fleet size you have in mind, and we will tell you plainly whether one-piece moulding or a fabricated box with liners is the better answer for that duty.

Product data parameters
Material
Expanded Polypropylene (EPP)
closed-cell
100% recyclable
Density
15–100 kg/m³ (customizable
up to 250)
Hardness
Shore C 15–50
Service Temperature
−40 °C to +130 °C
Compressive Strength
0.3–2.5 MPa
Compression Recovery
≥95% (compression set <40%)
Tensile Strength
≥450 kPa (up to 1000 kPa by density)
Water Absorption
<0.3% (virtually nil)
Flame Retardant
UL 94 HB / V-0 (optional)
FMVSS-302 PASS
Recyclability
100% recyclable
reusable
Product Catalogue
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.