+86-512-55391251 / +86-18901563989             zjgfhwm@zjgfenghui.cn
Pallet Boxes with Multi-Point Liners for Irregular-Shaped Parts
You are here: Home » Products » Combined Packaging » Pallet Box lining » Pallet Boxes with Multi-Point Liners for Irregular-Shaped Parts
Pallet Box with lining

loading

Pallet Box with lining Pallet Box with lining
Pallet Box with lining Pallet Box with lining
Pallet Box with lining Pallet Box with lining
Pallet Box with lining Pallet Box with lining
Pallet Box with lining Pallet Box with lining
Pallet Box with lining Pallet Box with lining

Pallet Boxes with Multi-Point Liners for Irregular-Shaped Parts

Availability:
Quantity:
An irregular part does not need a moulded cavity shaped exactly like itself. It needs three or four well-chosen points of support at its strongest faces, and everything between those points can stay open.
Product Description

An irregular part does not need a moulded cavity shaped exactly like itself. It needs three or four well-chosen points of support at its strongest faces, and everything between those points can stay open. That distinction decides whether a packaging project costs a fraction of the container price or several times it.

A full negative cavity is the right answer when one part number runs in high volume and its geometry is stable. For a family of castings, brackets and fabrications that changes with the product year, cutting a new cavity for every variant is neither affordable nor necessary. Multi-point support takes the middle path.

The principle is borrowed from fixturing. A rigid body is located by three points, restrained from tipping by one or two more, and cushioned at those points rather than wrapped everywhere. The part cannot translate, cannot rock, and the open space around it does no harm.

Choosing the points is the engineering step. Supports go on the part's existing datum faces and machined surfaces where it is designed to be held, and stay off thin walls, finished bores and painted areas. We read the drawing the way a machining fixture designer would, then transfer those faces into foam.

The liner set is layered accordingly. A base frame in hollow sheet carries the support blocks; the blocks themselves are moulded EPP at the density the load requires; and where a support face is delicate, an EPE or felt-faced cap softens the contact. Each element serves one job, which keeps the set simple to understand and to replace.

Variants within a family are handled with modular blocks. Support pads come in a small set of heights and angles, seated in a slotted base frame, so a taller casting uses the same frame with taller pads rather than a new liner set. Changeover between part numbers becomes a repositioning task measured in minutes.

Rolling and tipping are prevented geometrically. A V-notch accepts a cylindrical section and stops it spinning; an L-block braces an L-shaped bracket at both legs; a wedge holds a tapered housing against its flat face. None of these needs a full contour, only a correct opposing surface.

Loading stays fast because the layout is open. Operators can see where each block sits, place the part by eye rather than by alignment jig, and reach it with both hands on the way out. Closed cavities hide the part and slow the pick; this layout does neither.

Wear is local, so maintenance is local. A chipped support block is replaced as one item from stock, the frame and other pads stay in service, and a used set can be rebuilt in stores rather than reordered whole.

Provide drawings of the parts that travel together and the loads each one carries, and the layout you receive marks the support points, block grades and frame slots for the whole family.

Product data parameters
Material Options
PP Hollow Sheet
EPE Foam
EPP Molded Foam
Honeycomb Board
XPE
Corrugated Cardboard (coated)
Density
PP: 250–3500 g/m²
EPE: 18–45 kg/m³
EPP: 20–60 kg/m³
Honeycomb: 80–400 g/m²
Thickness
PP: 2–12 mm
EPE: 1–50 mm
EPP: 10–100 mm
Honeycomb: 6–50 mm
Custom Size Range
Inner L × W: 400×300 – 1800×1400 mm (match standard pallet box inner dims)
Structure Type
Flat divider
Layer pad
Fitted insert
Corner protector
U-channel liner
Compression Strength
PP ≥ 150 kPa
EPE ≥ 90 kPa
EPP ≥ 200 kPa
Honeycomb ≥ 500 kPa
Cushioning Performance
EPE/EPP: ≥ 90% recovery after 50% compression; PP/Honeycomb: rigid support
Temperature Resistance
PP: −20~+60 °C
EPE/XPE: −40~+70 °C
EPP: −40~+120 °C
Honeycomb: −30~+70 °C
Surface Treatment
Anti-static ESD (10⁶–10¹¹ Ω)
Conductive
UV-stabilized
PE-film laminated
Printed logo
Recyclability & Lifecycle
All materials recyclable (PP #5
PE #4); Reusable 200+ cycles vs cardboard single-use
Product Catalogue
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button
Previous: 
Next: 

Quick Links

Product Category

Contact Us

   +86-512-55391251 / +86-18901563989
  zjgfhwm@zjgfenghui.cn
   No. 5 Zhaofeng East Ring Road, Leyu Town, Zhangjiagang City, Jiangsu Province
Copyright © 2023 Zhangjiagang Fenghui logistics equipment Co., Ltd. Supported by Leadong. Sitemap. Privacy Policy.