Views: 0 Author: Site Editor Publish Time: 2026-11-16 Origin: Site
Walk through any automotive plant and you will see the same containers everywhere: 1200 × 1000 sleeve packs, 1200 × 800 pallet boxes, 600 × 400 small load carriers. They are standardised because the material handling system is standardised — conveyors, AGVs, racking, trailer widths, all built around a handful of footprints.
The parts inside them are the opposite. A die-cast housing has a machined bore on one face and a draft angle on the other. A valve body is all ribs and bosses. A bracket weighs 400 g and a transmission case weighs 40 kg. None of them were designed to fit a pallet footprint, and none of them should have to be.
That gap is filled by the thermoformed tray: a thin, deep-drawn plastic insert that turns a standard container into a part-specific one. The container stays in the fleet for a decade; the tray is what changes when the part changes.
This is the practical reason tray design deserves its own engineering conversation rather than being treated as an accessory ordered with the box.
Figure 1 — A foldable plastic container with a black vacuum-formed tray inside. The tray, not the box, positions the die-cast housing; the box only supplies walls, stacking strength and forklift access.
The tray in Figure 1 sits inside a foldable container and carries a single aluminium die-cast housing in a deep pocket. Look at what the tray is doing: it supports the part on its machined faces, holds it clear of the box walls, and leaves the space above it free for the next layer.
Figure 2 — A multi-cavity heavy-duty tray. One cavity is loaded to show the fit; the stacked trays behind show the nesting that makes the return leg cheap.
Figure 2 shows the other end of the range: a thicker, ribbed tray with repeated cavities, in a stack of empties. This is the version that replaces a set of dividers for a part family that arrives in volume.
Figure 3 — A three-cavity tray in blue. The small holes in each pocket are drainage and ventilation points, and the colour is a variant identifier as much as a cosmetic choice.
Figure 3 illustrates two details that are easy to miss and expensive to add later: drainage holes, and colour coding. Both are mentioned again below.
托盘看着就是一个成型件,功能上其实是5个部件各干一件事:
A tray looks like a moulded shape. Functionally it is five features doing five different jobs:
The cavity. A negative of the part, sized so the part locates without being forced. Too tight and operators stop seating parts properly; too loose and the part rocks.
Support pads and ribs. The contact points that carry the part's weight — placed on machined faces, casting ribs or designed flats, never on a sealing surface or a painted face.
The land between cavities. The flat area that carries the next tray, and the formed towers that stop neighbouring parts touching.
Drain and vent holes. In each pocket, so that wash water, condensate and coolant run off instead of pooling under the part.
The locating edge. A lip or step that keeps the tray from sliding inside the container, and that lets stacked trays sit square.
Miss any one of these and the tray still looks right in a photo. It fails in week six, at the customer's dock.
Buyers often ask for "the stronger one" without defining stronger against what. The difference between the two types in Figures 1–3 is concrete:
Standard tray | Heavy-duty tray | |
Sheet gauge | Thinner sheet, specified per part | Thicker sheet with deep ribbing, specified per load |
Load path | Part weight into the pocket floor | Part weight into ribs and formed columns, then into the container base |
Cycle life | Suitable for light parts and shorter loops | Built for repeated stacking under load |
Weight | Lighter, easier to lift for line-side handling | Heavier; check the lift before specifying |
Tooling | Lower cost, faster to sample | Higher tooling cost, longer lead time |
The rule of thumb here is a weight, not a feeling. Sheet gauge is quoted from the part weight, the support points and the cycle count rather than taken from a catalogue, and the tray is then sized so that a loaded layer stays inside the 50 kg manual handling limit.
Above that limit, nobody lifts the tray. The container carries forklift pockets and the unit is moved by forklift or pallet truck. A tray that protects the part but injures the operator is not a good design; it is a design that will be worked around, and worked-around packaging always ends up damaging parts.
The tray is designed against the container, not against the part alone. Four dimensions have to line up:
Footprint. Trays are sized to the internal dimensions of the container, with clearance for the wall draft — a 1200 × 1000 sleeve box does not have 1200 × 1000 of usable floor at the top of the sleeve.
Layer height. Cavity depth plus part height plus the tray land determines the sleeve height per layer. Sleeve height is built to the stack and the increment is customised per project, so tray depth and layer count are a joint decision rather than a compromise against a catalogue step.
Layer count. Parts per container = cavities per tray × layers. That number is set by the loaded stack height the trailer and warehouse allow, not by how many cavities fit on a sheet.
Stacking interface. Trays have to sit flat on each other, and the top layer needs a lid or a flat tray. A top layer that only looks flat will show up as a crushed part in the bottom layer.
This is why "send us a tray like this one" rarely produces a working system: the sample fits one container, at one sleeve height, for one part.
Draw depth versus draft. A deep pocket needs a draft angle to release from the mould without thinning the wall at the bottom. Pushing beyond what the material allows produces a tray that looks correct and cracks at the corner in the first month.
Support the part where it is strong. On the castings shown, the machined bore and the mounting faces are the correct support points; the thin outer wall is not. Supporting a part on its weakest feature is the most common cause of "the tray fits but the part arrives bent".
Clear the protrusions. Bleed screws, connectors, sensor bosses and studs need cavity depth above them, not just around them. A pocket that fits the part's silhouette but not its highest point will press the part down onto that point under the next layer's weight.
Radius the pocket edges. A sharp edge at the top of a cavity is a scraper. It marks painted parts on loading, and it is where the sheet starts to tear after a few hundred cycles.
Drain the pockets. Blind pockets collect wash water and condensate. A part sitting in 3 mm of water for a sea freight leg is a corrosion claim, not a packaging problem.
Colour as a control. Blue, grey and black trays in Figures 1–3 are not decoration. Colour per part family or per customer is the cheapest error-proofing available: a wrong tray in the wrong container is visible from across the plant.
Every loaded container that goes out has to come back. What comes back is either a folded sleeve plus a stack of trays, or a container full of trapped air.
Two properties make the difference:
Trays nest at 1:3. Three empty trays occupy the height of one loaded tray. Deep-drawn profiles nest better than shallow ones with tall ribs, which is why the return ratio is set at the tooling stage rather than discovered afterwards.
The container folds or collapses. Sleeve packs collapse to the pallet and lid; foldable containers fold to a fraction of their working height.
Combined, the empty return is usually the single largest freight saving in the system — larger than any reduction in packaging weight, and much larger than switching to a thinner sheet.
Part 3D data or a physical sample, plus weight per piece.
Container type and internal dimensions — sleeve box, foldable container or small load carrier, with the sleeve height range available.
Target parts per container and the loaded stack height allowed in the trailer and warehouse.
Surface condition — painted, coated, bare aluminium, or oiled; this decides support points and edge treatment.
Wash regime, if trays are cleaned between loops; it decides material and drainage.
Annual volume and loop length, which decide tooling investment and tray fleet size.
With those six, a tray quotation is a calculation. Without them, it is a guess with a price attached.
Can one tray design fit more than one container type? Only within the same footprint family. A tray for a 1200 × 1000 sleeve box will not fit a 1200 × 800 pallet box, but the same tray profile can usually be re-scaled for a second container with a new mould rather than a new design.
Which material should the tray be? HDPE and PP are the common choices for industrial parts: HDPE for chemical resistance and toughness, PP where higher service temperature matters, and modified PP where cold-impact strength is needed. ABS appears where stiffness and surface finish matter more than cost.
How many parts per tray is too many? Two limits apply and the lower one wins. The first is 50 kg per loaded layer: above that the tray is no longer handled by hand, and the unit moves by forklift or pallet truck through the container's forklift pockets. The second is stiffness — if the tray flexes enough to lose its locating fit, take a cavity out. Both are checkable at the sample stage by loading one tray and lifting it.
Do trays need drain holes if the parts are dry? If the loop includes washing, outdoor storage, sea freight or a humid plant, yes. Condensate forms even in a closed container, and a blind pocket is where it stays.
Can you produce trays for a container we already own? Yes, provided the internal dimensions and the stacking interface are measured rather than assumed. Send the container drawing or a measured sketch, and the tray is designed to that, not to a catalogue size.
Send the part data and the container you intend to use — or tell us the parts per container you need and let us propose the container and tray together — and we will come back with a tray layout, a layer plan and a return-volume estimate.